Is Secondary Glazing as Good as Double Glazing?
Is secondary glazing as good as double glazing? For most old houses, the honest answer is nearly, and in one important respect it is better. Secondary glazing with a low emissivity coating can cut heat loss through a window by over 60 percent, according to Historic England research, which closes most of the gap to modern double glazing. It usually beats double glazing on noise, costs far less, and it is often the only upgrade a listed building is allowed to have. But it is not identical. A modern argon filled double glazed unit still insulates better, seals better and lasts longer, and where you are free to replace your windows, double glazing remains the stronger thermal choice. This guide compares the two on the measures that matter: heat loss, noise, draughts, cost, condensation and planning rules, so you can decide which one fits your house.
Is secondary glazing as good as double glazing? The short answer
Is secondary glazing as good as double glazing? On warmth, it gets close but does not quite match. A single glazed window fitted with good secondary glazing typically reaches a U-value of around 1.8 to 2.8 watts per square metre per degree Kelvin, while a modern low emissivity argon filled double glazed unit sits at 1.0 to 1.4. The lower the U-value, the less heat escapes, so double glazing still wins on pure insulation. On noise, secondary glazing often wins, because the wide air gap between the old window and the new inner pane is better at damping sound than the narrow gap inside a sealed double glazed unit. On cost, secondary glazing wins by a wide margin. On listed buildings, there is no contest at all: secondary glazing is usually the only option, because it leaves the original windows untouched and can be removed again. The right choice depends on what your house needs most, and this guide works through each measure in turn.
What secondary glazing actually is
Secondary glazing is a second pane fitted on the inside of an existing window, in its own slim frame. It sits independently of the original frame, usually in aluminium or uPVC, and creates a sealed air gap between the old glass and the new pane. It is not the same thing as double glazing. Double glazing is a sealed unit with two panes bonded together, fitted inside a replacement window frame. Secondary glazing keeps your existing window and adds to it; double glazing replaces it.
That distinction drives almost every difference in this comparison. Because secondary glazing leaves the original window in place, there is no need to disturb historic joinery, no skip full of old frames, and usually no planning application. Because it is a separate inner window, it can be hinged, sliding or lift out, so you can still open the original window and clean both panes. The gap between the panes is much wider than the gap inside a sealed double glazed unit, typically around 100 millimetres, which matters for sound more than for heat, as explained below.
The panels come in several forms. Magnetic acrylic panels are the cheapest and lightest, and suit renters or a single cold room. Hinged and sliding aluminium frames are the standard fitted option for whole houses. Fixed panels are used where a window never needs to open. For the best thermal performance, ask for a low emissivity coating on the secondary pane, which reflects heat back into the room, and an insulating frame. Historic England found that the low emissivity coating is what lifts secondary glazing from a modest improvement to a reduction of over 60 percent in heat loss through the window.
Heat loss head to head
Is secondary glazing as good as double glazing for keeping heat in? The numbers say close, but not equal. The U-value measures how fast heat passes through a window, and a lower number means better insulation. Here is how the common options compare, using typical figures.
| Window type | Typical U-value (W/m2K) | What it means |
|---|---|---|
| Single glazing, as it stands | 5.0 to 5.8 | Heat escapes fast; cold glass, draughts, condensation |
| Single glazing plus secondary glazing | 1.8 to 2.8 | Below 2.0 with a low emissivity coating; most of the gap closed |
| Basic double glazing | 1.2 to 1.6 | Noticeably better than secondary glazing alone |
| Low emissivity argon filled double glazing | 1.0 to 1.4 | The current standard for replacement windows |
| Triple glazing | 0.6 to 0.8 | Best of all, at the highest cost and weight |
The table shows the real shape of the answer. Secondary glazing takes a terrible window, U-value around 5.0, and turns it into a respectable one, around 2.0 with a low emissivity coating. That is a large improvement, and Historic England research puts the reduction in heat loss through the window at over 60 percent. But a modern double glazed unit goes further, down to 1.0 to 1.4, and that gap matters across a whole house through a winter.
One detail surprises most people. For heat loss, the ideal gap between two panes is only 16 to 20 millimetres. A wider gap lets convection currents form inside the cavity, which carry heat across it. A secondary pane usually sits around 100 millimetres from the original glass, far wider than ideal, so much of its thermal benefit does not come from the air gap at all. It comes from the new frame being well sealed, which stops the uncontrolled air leakage that makes old sash windows so cold. In other words, secondary glazing fixes the draughts as much as it fixes the glass, and that is where a large share of the comfort gain comes from.
Building regulations set the benchmark. Replacement windows in existing homes in England must reach a U-value of 1.4 watts per square metre per degree Kelvin, or Window Energy Rating band B, under Part L of the Building Regulations. Secondary glazing on its own does not meet that standard, which is why it is not treated as a replacement window. But the regulations make an exception where character must be preserved: single glazing supplemented with low emissivity secondary glazing is accepted for historic buildings. That tells you how the two are officially viewed. Double glazing is the standard; secondary glazing is the approved alternative where the standard cannot apply.
Noise: where secondary glazing wins
If traffic, aircraft or a busy street is your problem, secondary glazing is often the better buy. Historic England notes that secondary glazing, unlike double glazing, can be highly effective at reducing noise. The reason is the gap. A sealed double glazed unit has a narrow cavity of 16 to 20 millimetres, which is tuned for heat, not sound. Secondary glazing leaves a gap of around 100 millimetres or more between the original pane and the new one, and that wider, uneven spacing damps a broader range of sound frequencies. Two panes of different thickness, separated by a wide gap, are a classic acoustic recipe.
Be careful with the numbers installers quote. You will see claims of 18 decibels, 25 decibels, even 45 decibels of reduction, and they are not comparable with each other. They depend on the glass thickness, the gap, the seals, the type of noise and how the test was done. No single figure is trustworthy as a promise for your house. What is reliable is the principle: for the same money, secondary glazing with acoustic laminated glass and a wide gap will usually quiet a room more than a standard double glazed replacement. If noise is your main complaint, that is the strongest argument for choosing secondary glazing even where double glazing is allowed.
Cost: the gap is large
Is secondary glazing as good as double glazing value for money? Here secondary glazing is clearly ahead. A fitted secondary glazing panel typically costs 300 to 500 pounds per window in the UK, depending on size, frame type and whether it opens. A full set of A-rated double glazed windows for a semi detached house typically costs around 4,800 pounds, according to the Energy Saving Trust, and that is before any making good to plaster and decoration after the old frames come out. For a house with ten windows, secondary glazing might cost 3,000 to 5,000 pounds all in, while replacement double glazing for the same house often runs to 5,000 to 9,000 pounds or more, with more disruption.
The savings side is where honesty matters. The Energy Saving Trust estimates that replacing all the single glazing in a semi detached home with A-rated double glazing saves about 85 pounds a year on energy bills in Great Britain, and 140 pounds in Northern Ireland, with a carbon saving of 290 kilograms a year in Great Britain. That is a small annual return on a large outlay, and it is why windows are usually justified by comfort and noise as much as by bill savings. The Trust does not publish a comparable annual saving figure for secondary glazing, and this guide will not invent one. What can be said is that secondary glazing costs much less up front for a large share of the thermal benefit, so its payback on bills alone is far shorter than double glazing, even though the absolute saving per year is smaller.
There is also a hidden cost to replacing windows that rarely appears in quotes: the disruption. Replacement means scaffolding for upper floors, old frames removed, new frames fitted, plaster and paint made good, and sometimes new internal sills. Secondary glazing is fitted from inside, room by room, usually in a day or two for a whole house, with no external work at all. For a household that cannot face a building site, that difference is worth real money.
Draughts and comfort
Old windows lose heat in two ways: through the glass, and through the gaps around it. In a sash window that has distorted over a century, the gaps can matter as much as the glass. Secondary glazing attacks both at once. The new inner frame is made to fit tightly, with proper seals, so it blocks the air leaking past the meeting rail, the box frame and the sash cords. Homeowners often report that the room feels warmer immediately, before the glass itself has done much, because the cold draught across the floor has stopped.
Double glazing does the same job, and does it slightly better, because a new sealed unit in a new frame is airtight by design. But the difference in comfort is smaller than the difference in U-values suggests. A well fitted secondary panel plus draught proofing on the original sash is a strong combination, and it is worth doing the draught proofing first if budget is tight. Our guide to how to stop draughts around windows and doors covers the cheap fixes, and how to make old windows less draughty deals specifically with sash windows. Either way, do not judge a window by its glass alone. The seals around it decide how the room feels on a cold evening.
Condensation: the honest drawback
Secondary glazing has one real weakness that double glazing does not share, and it is condensation between the panes. Warm moist air from the room can find its way into the cavity between the original window and the secondary pane. When it meets the cold outer glass, it condenses, and the trapped moisture can mist the glass, grow mould on the frame, or rot a timber sill. A sealed double glazed unit has a dry gas fill and a desiccant in the spacer bar, so this cannot happen inside it, though double glazing can still fail when its own seal breaks and the unit mists up permanently.
The risk is manageable, but only if the installation is done properly. Three things matter. First, the secondary frame must seal well against the wall and the reveal, so room air cannot leak into the cavity. Second, the cavity should be ventilated in a controlled way, usually with small vents or by opening the panel regularly, so any moisture that does get in can escape. Third, the original window should be in sound condition, with flaking paint and rotten timber repaired before the panel goes on, because trapped damp will make existing decay worse. Choose openable panels rather than fixed ones where you can, so you can air the cavity and clean both faces of glass. And keep the room ventilated as normal. Secondary glazing is not a substitute for dealing with damp; it makes a damp room worse if the moisture has nowhere to go.
Listed buildings and planning rules
For a listed building or a home in a conservation area, the comparison often ends here. Replacing original timber windows usually needs listed building consent, and consent is often refused where the windows contribute to the character of the building. Secondary glazing is different. Because it leaves the original windows unaltered and can be removed again, Historic England describes it as easily reversible in most cases, and it is the standard recommendation from conservation officers. In practice it rarely needs listed building consent, though that is not a guarantee: some listed buildings have stricter conditions, and a conservation area with an Article 4 direction can restrict what you do to the outside of the house. Secondary glazing sits inside, so it is usually unaffected, but always check with your local planning authority before ordering, and get the answer in writing.
The same logic applies to any period home you care about, listed or not. Original sash windows are part of what makes the house what it is, and they can be repaired, draught proofed and upgraded with secondary glazing for far less than replacement. If the frames are sound, there is rarely a good reason to throw them away. If they are rotten beyond repair, that is a different conversation, and replacement with like for like timber double glazing may be the honest answer.
Which one should you choose?
The decision turns on four questions: what is your house, what is your budget, what bothers you most, and how long will you stay? This table gives the short version.
| Your situation | Best choice | Why |
|---|---|---|
| Listed building or conservation area | Secondary glazing | Often the only option; reversible, no loss of historic fabric |
| Noise is the main complaint | Secondary glazing | Wide air gap and acoustic glass beat a standard sealed unit |
| Budget under 5,000 pounds for the whole house | Secondary glazing | Large share of the thermal benefit at a fraction of the cost |
| Frames are rotten or beyond repair | Double glazing | Replacement is needed anyway; fit the best unit you can |
| You want the best insulation and will stay decades | Double glazing | U-value 1.0 to 1.4 beats 1.8 to 2.8, and lasts 20 to 35 years |
| Rented home or short term stay | Secondary glazing | Cheaper, less disruptive, magnetic panels can even travel with you |
There is also a middle path that suits many old houses: secondary glazing now, on the worst rooms, and replacement double glazing later only where frames fail. You do not have to do the whole house in one go. Start with the bedrooms, where noise and cold matter most, and the rooms you sit in during the evening. The energy saving from windows alone is modest, around 85 pounds a year for a full double glazing replacement in a semi detached home, so spending the budget on the rooms you actually live in is the sensible order.
What to ask an installer
Whether you choose secondary glazing or double glazing, the installer matters as much as the product. For secondary glazing, ask these questions before you sign anything. Is the secondary pane low emissivity glass, and does the coating face outward? That single choice is what lifts the heat loss reduction above 60 percent. Are the panels openable, hinged or sliding, so you can ventilate the cavity and clean the glass? How is the cavity ventilated, and what stops condensation forming between the panes? What is the frame material, and is it insulated? What guarantee covers the seals and the fixings? And will they repair the original window first, including draught proofing the sash, so the secondary panel is not covering up a frame that is already failing?
For double glazing, ask for the whole window U-value and the Window Energy Rating, not just the glass specification, because the frame is part of the performance. Ask how the new frame will be sealed to the wall, and what making good is included in the price. Ask about trickle vents, because a new airtight window in an old house needs controlled ventilation or condensation will move to the next coldest surface. And ask for the expected lifespan in writing; the Energy Saving Trust puts good double glazing at 20 to 35 years with proper maintenance.
Get at least three quotes for either option, and compare them on the same specification: same glass, same frame, same number of openable panels, same making good. A cheap quote that leaves out the low emissivity coating or the draught proofing is not a bargain; it is a different product.
The verdict
Is secondary glazing as good as double glazing? It is nearly as good on heat, often better on noise, far cheaper, and the only choice for listed buildings. It is not as good at insulation in absolute terms, it needs care to avoid condensation, and it will not meet the U-value standard that replacement windows must hit. For an old house with sound frames, a tight budget, or a noise problem, secondary glazing is usually the smarter spend. For a house where the frames are failing, or where you want the best insulation available and plan to stay for decades, double glazing is worth the extra money. Either way, the worst option is to do nothing and keep heating the street through single glass. If you want the costs in detail before deciding, our guide to how much secondary glazing costs in the UK breaks down the price per window and the factors that push it up or down.
Frequently asked questions
Is secondary glazing as good as double glazing for heat loss?
Is secondary glazing as good as double glazing for heat loss? Nearly, but not quite. Secondary glazing with a low emissivity coating can reduce heat loss through a window by over 60 percent, according to Historic England, bringing a single glazed window to a U-value of around 1.8 to 2.8. Modern argon filled double glazing reaches 1.0 to 1.4, so it insulates better. Secondary glazing closes most of the gap at a fraction of the cost.
Is secondary glazing better than double glazing for noise?
Often yes. Secondary glazing leaves a wide air gap of around 100 millimetres between the original pane and the new one, and that wider gap damps a broader range of sound than the narrow 16 to 20 millimetre gap inside a sealed double glazed unit. Historic England describes secondary glazing as highly effective at reducing noise. For the best result, ask for acoustic laminated glass and a well sealed frame.
How much does secondary glazing cost compared with double glazing?
Secondary glazing typically costs 300 to 500 pounds per window fitted in the UK. A set of A-rated double glazed windows for a semi detached house typically costs around 4,800 pounds, according to the Energy Saving Trust. For a whole house, secondary glazing is usually far cheaper, with less disruption, because it is fitted from inside and the original frames stay in place.
Does secondary glazing need planning permission?
Usually not. Secondary glazing is fitted inside the house, leaves the original windows unaltered, and is easily reversible in most cases, so it rarely needs listed building consent or planning permission. But rules vary by building and by council, and some listed buildings have stricter conditions, so always check with your local planning authority before ordering.
Does secondary glazing cause condensation?
It can do, if the cavity between the panes is not sealed and ventilated properly. Warm moist room air leaking into the cavity condenses on the cold outer glass. The fix is a well sealed secondary frame, controlled ventilation of the cavity, openable panels so you can air and clean it, and repairing the original window first. A sealed double glazed unit cannot mist up inside unless its own seal fails.
How long does secondary glazing last?
A well fitted secondary glazing panel can last decades, because there is no sealed gas unit to fail. The parts that wear are the seals, hinges and fixings, which can be replaced. Good double glazing lasts 20 to 35 years according to the Energy Saving Trust, after which the sealed units can mist up and need replacing. Secondary glazing has no sealed unit to fail, which is a genuine long term advantage.
Sources
- Historic England, Energy Efficiency and Historic Buildings: Secondary glazing for windows. https://historicengland.org.uk/images-books/publications/eehb-secondary-glazing-windows/
- Energy Saving Trust, Energy efficient windows and doors. https://energysavingtrust.org.uk/advice/windows-and-doors/
- Department of Energy and Climate Change, Buyer guide: Choosing the best windows and glazing for your home (2016). https://assets.publishing.service.gov.uk/media/5a802d7aed915d74e33f8e80/DECC_factsheet_11.11.16_GLAZING_LOCKED.pdf
- Green Retrofit Guide, How Much Does Secondary Glazing Cost in the UK? https://greenretrofitguide.com/secondary-glazing-cost-uk/