Is Double Glazing Better Now Than 20 Years Ago?
Is double glazing better now than 20 years ago? Yes, and the improvement is not marginal. A typical double glazed window fitted in 2006 let roughly twice as much heat escape as a good one fitted today, and the gap is wider still once you count draughts, condensation and the slow decay of a twenty year old sealed unit. The change did not come from one breakthrough. It came from better glass coatings, argon gas, warm edge spacers, stronger frames and a set of building rules that kept raising the bar. This guide explains what actually changed, what the numbers say, and whether your own twenty year old windows are worth replacing.
Is double glazing better now than 20 years ago? The short answer
Yes. A double glazed window installed in 2006 typically had a whole window U-value of about 2.0 watts per square metre kelvin, written as 2.0 W/m2K. A good double glazed window installed in 2026 has a U-value of 1.2 to 1.4 W/m2K, and the best reach 1.0 or lower. That is roughly a third less heat escaping through the same sized window. The improvement is real, measurable and written into the building regulations, the energy rating labels and the EPC assumptions your home is assessed against. The honest caveat is that windows are only one part of a home heat loss, so the saving on your bill is smaller than the improvement in the glass. Replacing single glazing is where the big saving sits. Replacing sound twenty year old double glazing is a comfort and condition decision more than a money decision, and the sections below explain why.
What your 2006 windows actually were
To judge the progress fairly, it helps to know what a normal 2006 window was. Double glazing had been the UK standard for decades by then, and the worst single glazing was already disappearing from most homes. But the typical unit of twenty years ago was a simpler product than the one installers fit today.
Most 2006 double glazed units had two panes of ordinary float glass with a 16 millimetre gap filled with ordinary air, held apart by an aluminium spacer bar. A hard coat low emissivity coating, sold under names such as Pilkington K Glass, was available and increasingly common, but it was not universal, and soft coat low emissivity glass with argon gas was still a premium upgrade rather than the default. The frames were usually early multi chamber uPVC or aluminium without the thermal breaks that are standard now. Seals were good for their day, but the airtightness testing and trickle ventilation rules that shape modern windows were less developed.
None of that made a 2006 window bad. It was a large step up from single glazing, and many of those windows are still in service today. But it was built to a different standard, because the standard of the time asked less of it. The 2002 edition of Part L of the Building Regulations required windows in new dwellings to reach a U-value of 2.0 W/m2K or better, and that was the bar most of the market aimed at. Today the bar for a replacement window is 1.4 W/m2K, and the notional new home used to set energy targets assumes windows of 1.2 W/m2K. The market moved because the rules moved, and the rules moved because the technology made better performance affordable.
The numbers: 2006 double glazing vs 2026 double glazing
U-value is the measure that matters most for heat loss. It states how much heat passes through one square metre of window for each degree of temperature difference between inside and outside, and a lower number is better. The table below uses the U-values that EPC assessors assume for windows of different ages, plus the typical values published for modern glazing types. EPC assessors use these defaults when they cannot see a rating label, so they are a fair picture of what the industry expects from each era. Read the table as the direct answer to the question, is double glazing better now than 20 years ago, in numbers rather than adjectives.
| Window type | Typical whole window U-value |
|---|---|
| Single glazing | 4.8 W/m2K |
| Double glazing fitted before 2002 | 2.7 to 3.1 W/m2K |
| Double glazing fitted 2002 to 2021 | 2.0 W/m2K |
| Double glazing fitted 2022 or later | 1.4 W/m2K |
| Modern double glazing, low-E coating and argon | 1.0 to 1.4 W/m2K |
| Modern triple glazing | 0.8 to 1.0 W/m2K |
| Passivhaus standard windows | Below 1.0 W/m2K |
Read the table as a story of steady progress rather than a single leap. A pre 2002 unit at around 2.8 loses about twice as much heat as a 2026 unit at 1.4. A 2006 unit at 2.0 loses about 40 percent more heat than a 2026 unit at 1.2. That is a genuine improvement, and it is the reason the Energy Saving Trust and the building regulations both treat a 2026 window as a different product from the one your home may already have.
The U-value is not the whole story, though. The Window Energy Rating looks at the whole window, including the frame, and counts solar gain and air leakage as well as heat loss. A window can have a decent U-value and still be a poor window if it leaks air around the seals. Modern windows are tested for air leakage in a way that 2006 windows generally were not, and the rating label, which runs from A++ down to E, makes the result visible to buyers. That transparency is itself one of the biggest changes of the last twenty years.
Five things that changed inside the glass
The glass unit is where most of the improvement happened. Five changes, each small on its own, are why the answer to is double glazing better now than 20 years ago is yes, and together they add up to the difference between 2.0 and 1.2.
1. Low emissivity coatings became standard
A low emissivity coating, usually called low-E, is a microscopically thin layer of metal oxide on the inner face of one pane. It reflects long wave heat radiation back into the room while letting daylight through. Hard coat low-E glass was available twenty years ago, but soft coat low-E, which insulates better, has become the norm in quality units. A 2004 Pilkington comparison of a typical uPVC window shows the effect clearly. With hard coat low-E glass and an air filled cavity, the window scored a band E energy rating. The same window with soft coat low-E glass and argon reached band C. The coating alone moved the window two bands.
2. Argon replaced air in the cavity
The gap between the panes is no longer usually filled with ordinary air. Argon, an inert gas, has about 34 percent lower thermal conductivity than air, so it slows heat transfer across the cavity. Argon filled units are now the standard for quality installations in the UK, and krypton, which insulates better still, is used in some slim triple glazed units. The gas is sealed inside the unit at manufacture, and a good seal keeps most of it there for decades. The British standard for sealed units, BS EN 1279-3, allows gas leakage of up to 1 percent per year, which means a unit filled with 90 percent argon should still hold about 70 percent of its gas after twenty years.
3. Warm edge spacers replaced aluminium bars
The spacer bar holds the two panes apart and seals the edge of the unit. Aluminium conducts heat easily, so the edge of an old unit was a cold bridge where heat escaped and condensation formed. Warm edge spacers, made from foam or rigid plastic composites, conduct far less heat. The first foam warm edge spacer was introduced in 1989, but it took years to become the industry default, and it is now standard in quality sealed units. The difference shows up at the edges of the glass, where modern windows stay warmer and clearer on cold mornings.
4. Cavities got wider and seals got better
The insulating gap in a modern unit is usually 16 to 20 millimetres, the width that gives the best balance between insulation and convection inside the cavity. Go narrower and the panes are too close to insulate well. Go much wider and air starts to circulate inside the gap and carry heat across it. Modern units also use better primary and secondary edge seals, applied under controlled factory conditions, which is why a well made modern unit can retain over 90 percent of its original gas fill for more than twenty years.
5. Triple glazing arrived for ordinary homes
Triple glazing was once a niche product for very cold climates and Passivhaus projects. It is now a mainstream option in the UK, typically reaching U-values of 0.8 to 1.0 W/m2K. It is heavier and more expensive than double glazing, and the extra pane brings a small loss of daylight, so it suits north facing rooms, noisy streets and homes aiming for the highest fabric standard. For most homes, a good A-rated double glazed unit is the sweet spot, and triple glazing is the upgrade for specific rooms rather than the whole house.
Frames got better too
The glass gets the attention, but the frame is a third of the window, and frames have improved as much as the glass. Early uPVC frames were simple two or three chamber profiles. Modern uPVC frames have five or six insulating chambers, and some, such as the Rehau Geneo six chamber profile, can reach whole window U-values as low as 0.7 W/m2K. Aluminium frames, which conduct heat readily, now have polyamide thermal breaks, an insulating barrier between the inner and outer aluminium, that was rare twenty years ago. Timber frames have better factory applied coatings and engineered sections that move less with moisture, so they seal better for longer.
Seals and gaskets have improved alongside the frames. Modern windows close against continuous compression seals rather than the brush seals common on older frames, and the hardware holds the sash tightly against the frame at several points instead of one. The result is a window that leaks far less air, which matters because draughts around a window can waste as much heat as the glass itself. The Energy Saving Trust notes that modern windows are usually more airtight than old ones and will usually have trickle ventilators to provide controlled background ventilation, which should be kept open.
The rules that forced the improvement
Technology alone does not explain the change. The rules kept moving, and each move pushed the market.
In 2002, Part L of the Building Regulations set a U-value of 2.0 W/m2K for windows in new dwellings, and the Fenestration Self-Assessment Scheme, FENSA, was established the same year to certify installers. In 2004 the British Fenestration Rating Council launched Window Energy Ratings, giving buyers a simple A to G label for the whole window, based on heat loss, solar gain and air leakage. The scheme was recognised under the Energy Efficiency Commitment in November 2004. In 2010 the Building Regulations were rewritten so that replacement windows needed a minimum Window Energy Rating of band C.
The biggest single step came in June 2022, when the Part L uplift took effect in England. Replacement windows in existing homes must now reach a U-value of 1.4 W/m2K, down from 1.6, or a Window Energy Rating of band B, up from band C. Windows in new dwellings moved from a limiting value of 2.0 to 1.6, with the notional dwelling used for energy targets assuming 1.2. Looking ahead, the Future Homes Standard is expected to use a reference window U-value of 0.8 W/m2K, which would make triple glazing or vacuum glazing the norm for new homes. The 2026 edition of Approved Document L, which takes effect on 24 March 2027, keeps the 1.4 or band B standard for replacement windows.
The effect of this ratchet is visible in the EPC defaults. An assessor assumes 2.0 for double glazing fitted between 2002 and 2021, and 1.4 for glazing fitted from 2022 onwards. If your windows date from 2006, your EPC already assumes they lose about 40 percent more heat than a new set, and it will keep assuming that until they are replaced.
What 20 years does to a sealed unit
There is a second reason the question matters now. A window fitted in 2006 is twenty years old, and twenty years is close to the expected life of a sealed unit. The typical lifespan of a double glazed sealed unit in the UK is 15 to 25 years, depending on the quality of the materials, the standard of installation and the exposure of the elevation. The frame may last 20 to 35 years, but the sealed glass unit is the shorter lived part.
The failure mode is slow and quiet. Sunlight and temperature cycles stress the edge seal, and the argon gradually escapes while moist air creeps in. The British standard allows up to 1 percent gas loss per year, so a good unit still holds most of its gas after two decades, but a poor unit, or one on a sunny south facing wall, can lose it much faster. Units built in the 1990s with aluminium spacer bars often failed at 12 to 15 years. Once the desiccant inside the spacer is saturated, moisture condenses between the panes, and the unit mists up from the inside. That misting cannot be wiped away, because it is trapped between the glass, and it is the clearest sign that the seal has failed.
A failed unit insulates little better than single glazing, so a misted 2006 window is not just ugly, it is performing far below the 2.0 it was built to. The good news is that a failed unit does not mean a failed window. A glazier can usually swap just the sealed unit and keep the frame, at a typical cost of 80 to 150 pounds per unit. That is worth knowing before you accept a quote for full replacement, because a sound frame with new glass can perform close to a brand new window at a fraction of the cost.
Is it worth replacing 20-year-old double glazing?
This is where honesty matters more than enthusiasm. The Energy Saving Trust says that upgrading a single glazed semi-detached home to A-rated double glazing saves about 85 pounds a year on energy bills in Great Britain, and 140 pounds in Northern Ireland, while cutting carbon dioxide by 290 kilograms a year in Great Britain. Those are the most quoted window saving figures in the UK, and they apply to replacing single glazing. Replacing working twenty year old double glazing saves far less, because the starting point is already 2.0 rather than 4.8.
Which? puts it plainly, quoting an installer who says customers often think new windows will make a big difference to their heating bills and pay for themselves, but unless you are replacing old single glazed windows the difference is often small. A set of A-rated windows for a semi-detached house typically costs around 4,800 pounds, according to the Energy Saving Trust. At the saving from a single glazing upgrade, that is a payback of many decades. From old double glazing, the energy payback alone is longer still, and no honest guide should pretend otherwise.
That does not mean replacement is a bad idea. It means the reasons to replace are comfort, condition and noise rather than a quick payback. Replace your twenty year old windows if the sealed units have misted, if you can feel draughts around the frames, if the handles and hinges are failing, if condensation pools on the inside of the glass on cold mornings, or if traffic noise has become intrusive. A new A-rated window will feel warmer to sit beside, because the inner pane stays closer to room temperature, and it will cut outside noise noticeably. Those are real benefits, and they are the benefits that homeowners actually notice. Treat the energy saving as a bonus, not the reason.
If your 2006 units are still clear, draught free and easy to operate, the sensible move is usually to keep them and spend the money where it saves more. Loft insulation, cavity wall insulation and draught proofing all pay back faster, and secondary glazing can lift a sound old window close to modern performance without the cost of full replacement. Our guides to Is Secondary Glazing as Good as Double Glazing? and What Are the Downsides of Secondary Glazing? explain that trade off in detail, and How Much Does Secondary Glazing Cost in the UK? gives the price comparison.
How to check how good your windows are
You do not need a surveyor to get a rough answer. Start with the paperwork. A FENSA certificate, which installers have issued since 2002, records the installation date and confirms the windows met the building regulations in force at the time. The BFRC rating label, if it is still on the frame or in the paperwork, shows the Window Energy Rating band. Your EPC, if you have one, states the assumed glazing type and age band.
Then look at the glass. Misting between the panes means a failed seal and a unit that needs replacing. Condensation on the inside surface on cold mornings points to high indoor humidity or a cold inner pane, and modern low-E glass reduces it. Condensation on the outside of the glass, oddly, is a sign of a very efficient window, because it means so little heat is escaping that the outer pane stays cold, and it clears quickly without causing damp.
Finally, check the frames. Hold your hand near the edges on a cold day and feel for draughts. Try the handles and hinges. Look for gaps in the seals and for daylight visible around a closed sash. A window that is sound, clear and draught free is doing its job, even if it is twenty years old. A window that mists, rattles or leaks air is not, and the glass or the whole unit deserves attention. If you do replace, use an installer registered with a competent person scheme such as FENSA, get at least three quotes, and check that the quote states the whole window U-value or the Window Energy Rating band, not just the centre pane figure. The Energy Saving Trust also recommends the government endorsed TrustMark scheme and the Glass and Glazing Federation for finding installers, and its windows and doors guide is the clearest independent starting point.
The verdict
Is double glazing better now than 20 years ago? Yes, by a clear and measurable margin. The glass insulates better, the gas fill lasts longer, the edges stay warmer, the frames seal tighter and the labels tell you the truth about the whole window instead of leaving you to guess. A 2006 window at 2.0 W/m2K against a 2026 window at 1.2 W/m2K is a real step forward, driven by low-E coatings, argon, warm edge spacers and twenty years of tightening building regulations. But the improvement is a reason to replace failed or draughty windows, not a reason to rip out sound ones. Check your seals, look for misting, and spend first on the measures that save the most. When your windows do need replacing, the product you buy today is genuinely, measurably better than the one fitted twenty years ago, and your home will feel the difference on the first cold night.
Frequently asked questions
Is double glazing better now than 20 years ago?
Yes. A typical 2006 double glazed window had a U-value of about 2.0 W/m2K, while a good 2026 window reaches 1.2 to 1.4 W/m2K, roughly a third less heat loss. Low-E coatings, argon gas, warm edge spacers, better frames and tighter building regulations all contributed.
What U-value should new double glazing have in the UK?
A replacement window in an existing home in England must reach a U-value of 1.4 W/m2K or a Window Energy Rating of band B under Part L of the Building Regulations. Aim for 1.4 or lower, and treat 1.2 as a good target for a quality A-rated window.
How long does double glazing last?
The sealed glass unit typically lasts 15 to 25 years, while the frame usually lasts 20 to 35 years. Misting between the panes is the clearest sign that the seal has failed and the unit needs replacing, even if the frame is still sound.
Can you just replace the glass in old double glazing?
Yes. A glazier can usually swap just the failed sealed unit and keep the existing frame, at a typical cost of 80 to 150 pounds per unit. This is much cheaper than full window replacement and restores most of the thermal performance.
Is triple glazing worth it over modern double glazing?
Triple glazing typically reaches 0.8 to 1.0 W/m2K against 1.0 to 1.4 for good double glazing, so the extra saving is modest in the mild UK climate. It is worth considering for north facing rooms, noisy streets and homes aiming for the highest fabric standard, but for most homes a good A-rated double glazed unit is the better value.
Do new windows need trickle vents?
Modern windows are much more airtight than old ones, so they usually have trickle ventilators, also called background ventilators, to provide controlled ventilation. Keep them open, as the Energy Saving Trust advises, to manage moisture and indoor air quality.
Sources
- Energy Saving Trust, Energy efficient windows and doors, https://energysavingtrust.org.uk/advice/windows-and-doors/
- GOV.UK, Conservation of fuel and power: Approved Document L, https://www.gov.uk/government/publications/conservation-of-fuel-and-power-approved-document-l
- Pilkington, Window Energy Ratings bulletins, July 2004 and January 2007, https://www.pilkington.com/-/media/pilkington/site-content/uk/reference/werbulletin3.pdf
- Glass Times, U-volution of an industry, https://glasstimes.co.uk/featured-articles/u-volution-of-an-industry/
- SEH BAC, Sustainability in the industry: how far has glazing come?, https://www.sehbac.com/blog/sustainability-in-the-industry-how-far-has-glazing-come
- Which?, Your double glazing questions answered, https://www.which.co.uk/reviews/double-glazing/article/your-double-glazing-questions-answered-axmeM9O8g4FO
- Double Glazing Units, Double Glazed Units Replacement: When and How, https://www.doubleglazingunits.co.uk/blog/double-glazed-units-replacement