What Happens to Cavity Wall Insulation After 25 Years?
What happens to cavity wall insulation after 25 years? In most homes, nothing dramatic. The guarantee runs out, the paperwork gets harder to find, and the insulation itself usually keeps working exactly as it did the year before. The 25 year mark is not an expiry date. It is the end of a warranty, and the two things are routinely confused, by homeowners, by buyers, and sometimes by the tradespeople who quote for the work that follows. This article explains what actually changes at 25 years, what happens to each type of insulation material over that time, how to tell whether yours is still doing its job, and what your options are when the guarantee has gone.
It matters now because the big wave of cavity wall insulation in Britain is ageing into that question. Millions of homes were filled in the 1980s, 1990s and 2000s, and a large share of those installs are now at or past the 25 year line. If your house is one of them, you will face the question at some point, either when a room feels cold, when a surveyor mentions it during a sale, or when a letter arrives offering to check it for you. Knowing what the guarantee covered, what the material does over decades, and what a proper check looks like will save you from paying for work you do not need, and from ignoring work you do.
The short answer: what happens to cavity wall insulation after 25 years?
What happens to cavity wall insulation after 25 years is mostly paperwork, not physics. The 25 year guarantee issued by the Cavity Insulation Guarantee Agency, known as CIGA, comes to an end, which means defects in the material or the installation are no longer put right free of charge under that guarantee. The insulation itself does not switch off. Mineral wool, polystyrene beads and polyurethane foam are all designed to last far longer than 25 years when they were installed correctly into a dry, suitable wall. The Energy Saving Trust says installation work should be guaranteed for 25 years by CIGA or an independent insurance backed guarantee, and that 25 year figure is about consumer protection, not about the material wearing out on a schedule.
There are exceptions, and they are the reason this question gets asked so often. Some fills do fail before or around the 25 year mark: loosely blown fibre can slump to the bottom of the cavity, old urea formaldehyde foam can shrink and crumble, and any fill can get wet if the outer wall has deteriorated. But those are failures of a particular install in a particular wall, not a property of turning 25. A dry, well installed fill in a sound wall can keep insulating for the life of the building. The honest answer to the question is therefore a check, not a calendar date: find out what material is in your walls, whether it is still dry and in place, and whether the guarantee is still live. The rest of this article walks through each of those steps.
Why 25 years is the number everyone quotes
The 25 year figure comes from the guarantee, and the guarantee exists because cavity wall insulation is invisible once it is in. You cannot see whether it was installed well, whether it fills the cavity evenly, or whether it is still there ten years later. The industry set up CIGA in 1995 as an independent guarantor, and a CIGA guarantee runs for 25 years from the date of installation for work fitted by a registered installer. That length was a deliberate choice: long enough to cover the realistic life of a claim about workmanship or materials, and short enough that an insurer would underwrite it. It was never a statement that the insulation itself lasts 25 years and then stops.
The Energy Saving Trust repeats the figure in its cavity wall insulation guide, telling homeowners that installation work should be guaranteed for 25 years by CIGA or have an independent insurance backed guarantee. That advice is about what to demand before you pay, not about what happens afterwards. The same guide notes that a typical install in Great Britain costs around 2,200 pounds and that about 33 percent of all the heat lost in an uninsulated home escapes through the walls, which is why the measure was sold so widely in the first place.
Confusion creeps in because 25 years also appears in a second context. Trade guides commonly describe cavity wall insulation as lasting 25 to 40 years, and some describe modern materials as lasting the lifetime of the building. Both can be true at once: 25 years is the guaranteed minimum horizon, and the realistic service life of a good install in a dry wall is much longer. The number that matters for your house is not the one in the brochure. It is the condition of your walls and the material inside them.
What the CIGA guarantee actually covers
A CIGA guarantee is narrower than most homeowners assume, and understanding its limits is the first step to knowing what changes when it expires. CIGA acts as guarantor for 25 years for cavity wall insulation fitted by registered installers, and where a guarantee holder has a problem caused by workmanship or materials, CIGA works with the installer, or steps in itself where that is not possible, to put the problem right. That is the core promise, and it is a useful one: if the fill was put into an unsuitable wall, if it was installed at the wrong density, or if the material itself was defective, the guarantee is the route to a free fix.
What it does not cover matters just as much. CIGA has said plainly that its guarantee covers defects in workmanship or materials in connection with the installation, rectified free of charge for 25 years, but that it does not include indirect loss, damage, costs or expenses, and it does not cover failures in building maintenance. If your pointing has failed, your gutters leak, or your render has cracked and rain is getting into the wall, that is a maintenance problem, not an insulation problem, and neither the installer nor CIGA will pay to fix it. CIGA has also said it cannot guarantee the performance of the product once installed, because performance depends on ventilation, heating control and the condition of the building.
The guarantee also has a claims record that puts its scale in perspective. Industry analysis of CIGA figures has put claims at around 4 for every 1,000 guarantees, which suggests most installs never generate a claim at all. That is worth remembering when a cold caller tells you that every 25 year old install is a disaster waiting to happen. It is not. The guarantee is a safety net for the minority of installs that go wrong, and for most homes it simply sits in a drawer, unused, until it expires.
One practical point: the guarantee is linked to the property, not the person who paid for the work, so it generally passes to a new owner when the house is sold. If you bought a house with insulation already in place, you may be covered even though you never met the installer. The catch is the paperwork. If you do not have the certificate, you need to ask CIGA whether your address is registered, and CIGA charges more than 50 pounds for a copy or replacement certificate, according to consumer guidance. Check before the guarantee expires, because after expiry there is nothing to claim under, and the certificate is still useful evidence of what was installed and when.
What happens to each type of insulation after 25 years
Not all cavity fill ages the same way. What happens after 25 years depends mostly on which material is in your walls, and the differences are large enough to change the advice. There are four materials you are likely to find in a British home of this age.
Expanded polystyrene beads, usually called EPS beads, are the longest lived of the common fills. The beads are blown in with an adhesive that bonds them into a mass, they do not absorb water, and they do not rot or support mould growth. Trade guidance commonly describes them as capable of lasting the lifetime of the building, and they are the material most often recommended for exposed elevations precisely because water does not degrade them. After 25 years, bonded beads in a dry wall should look much as they did on the day they went in. The main risk is not age but a bad install: unbonded beads can pour out if someone cuts into the wall, and voids can be left where the beads did not flow around wall ties or mortar droppings.
Mineral wool, also called blown fibre, is the oldest of the modern fills and the one with the most mixed record. It is glass or rock wool blown in as loose fibres, and when it is dry and undisturbed it insulates well for decades. Trade guides typically put its lifespan at 50 to 100 years. Its weakness is water and gravity. Loosely blown fibre can settle over the years, compacting into the bottom of the cavity and leaving the top of the wall bare. That slump is the classic pattern behind cold bedrooms over warm living rooms. Wet mineral wool is worse: it acts like a sponge, bridging the cavity and wicking water to the inner leaf, and wet fill insulates poorly, so the wall gets damp and cold at the same time. A 25 year old mineral wool fill in a dry, sheltered wall is usually fine. The same fill in an exposed wall with tired pointing is the install most likely to have failed.
Polyurethane foam is injected as a liquid that expands to fill the cavity, giving excellent coverage around awkward shapes. Trade guidance typically puts its lifespan at 50 to 80 years. Modern polyurethane is a different chemistry from the foams of the 1970s, and it is much more chemically stable, holding its shape and its insulating value for decades when it stays dry. Its main enemy is the same as every other fill: water getting in from a failed outer leaf, and physical disturbance from later building work.
Urea formaldehyde foam, known as UFFI, is the material to watch for in the oldest installs. It was used mostly in the 1970s and early 1980s, pumped into cavities as a foam mixed on site. It suffers from considerable shrinkage over time, and inspectors have found gaps of an inch or more on each side of a foam block where it has pulled away from the wall. It also deteriorates on contact with moisture, and wet UFFI should be removed by a specialist. It was banned in Canada in 1980 and in the United States in 1982 over fears about formaldehyde off-gassing, though it was never banned in Europe and is still used there. If your house was insulated in the late 1970s or early 1980s and nobody can tell you what went in, UFFI is the material a surveyor will want to rule out first, because shrinkage and crumbling are its normal ageing pattern, not a surprise failure.
The three ways old cavity wall insulation actually fails
When a 25 year old fill does fail, it almost always fails in one of three ways, and each has different symptoms and a different fix. Knowing which one you are looking at stops you paying for the wrong remedy.
The first is wet fill. Rain drives through the outer leaf faster than the wall can dry, usually on an exposed elevation or where the pointing, render or gutters have failed. Fibre fill soaks it up and carries it across the cavity to the inner leaf. The symptoms are damp patches on internal walls, mould behind furniture on external walls, and a wall that feels cold even when the heating is on. Wet fill is the most serious failure, because it makes the house colder and damper at the same time, and because the fix starts outside the cavity: the outer leaf has to be repaired first, or any new insulation will get wet the same way.
The second is slump. Loosely blown fibre settles over the years and compacts into the bottom of the cavity, leaving the upper part of the wall uninsulated. The symptoms are patchy and easy to misread: cold spots high on a wall, a bedroom that never warms up while the room below is comfortable, or a blotchy pattern on a thermal imaging camera. Slump is a slow failure, and it is the one most often found in fills that are 25 years old, because it is a function of time and gravity rather than a single event.
The third is voids and cold spots. Fill blown in from a grid of drill holes has to flow around wall ties, mortar droppings and debris in the cavity, and it does not always get everywhere. The result is unfilled pockets that show up as cold patches. Voids are usually an installation failure from day one rather than an ageing failure, but they only get noticed years later, often when a thermal survey is done for another reason. A fill with voids was never doing its full job, and age has nothing to do with it.
How to tell whether your insulation is still working
You cannot see cavity wall insulation, so checking it takes a bit of detective work. Start with the cheap checks before you pay anyone. Look at the outside of the house for the drill pattern: a filled cavity usually leaves mortar coloured dots roughly a metre apart in the joints, neatly re-pointed. If a previous owner never mentioned insulation and the paperwork is long gone, the wall still keeps the record. Check your Energy Performance Certificate, which may show whether the cavity is insulated, and ask your local authority building control department, which may hold records of the work.
Inside the house, the symptoms of a failed fill are specific enough to be useful. Damp patches or mould on external walls, especially behind furniture, point to wet fill. A room or a section of wall that never warms up, while the rest of the house is comfortable, points to slump or voids. Blown or spalling bricks, cracked render and failed pointing on the outside are not symptoms of the insulation, but they are the conditions that let water in and turn a working fill into a wet one, so they belong on the same checklist.
The decisive check is a borescope inspection. An installer drills a small hole in a mortar joint and puts a camera into the cavity to see what is actually there: whether the cavity is filled, what material it is, whether it is wet, whether it has slumped, and whether there is rubble or debris. The Energy Saving Trust recommends a borescope inspection as one of the ways to check for existing insulation, and reputable installers offer it as a survey before they recommend any work. It takes minutes, it settles the question, and nothing sensible should be priced before it is done. A thermal imaging survey is a useful second step: it maps cold spots across a whole elevation and shows slump and voids as blotchy patterns, but it cannot identify the material or tell wet fill from missing fill, so it complements the borescope rather than replacing it. That is how you answer what happens to cavity wall insulation after 25 years for your own house: with a camera in the cavity, not a date on a certificate.
Two warnings belong here. First, treat cold callers and leaflets offering a free insulation health check with care. A genuine check is a borescope and a written report from a registered installer or a surveyor, not a sales visit that ends with a quote for extraction. Second, do not let anyone drill exploratory holes all over the house. One hole in a mortar joint, properly made good, is enough to see inside a cavity.
What to do when the guarantee has run out
If your guarantee has expired and the insulation is working, the correct action is usually nothing. There is no rule that says a fill must be replaced at 25 years, and no source supports a hard expiry. Keep the outer wall in good repair, because pointing, render, gutters and downpipes are what keep the fill dry, and a dry fill keeps working. That maintenance is the real 25 year task, and it matters more than the date on the certificate.
If the guarantee is still live and you have a problem, act before it expires. The route is the one the Energy Saving Trust sets out: call the installer first, give them the chance to inspect and fix it, and if they will not help or no longer exist, use the CIGA certificate and contact CIGA. CIGA will arrange an inspection and, where the problem is a defect in materials or workmanship, remedial work. Keep copies of every letter and email, note the dates of phone calls, and if a claim is declined, ask for the reasons in writing and check the complaints route. A guarantee near the end of its term is a reason to move quickly, not a reason to panic.
If the guarantee has expired and the fill has failed, you are paying for the fix yourself, and the choice is between three options. The first is to leave a failed fill in place and manage the symptoms, which is rarely sensible if the fill is wet, because wet insulation makes the house colder and damper. The second is extraction and refill: a specialist removes the old material, cleans the cavity, lets it dry, and installs new insulation if the wall is suitable. The third is to leave the cavity empty and insulate the wall another way, usually from the outside, which is the honest fix for a wall that should never have been filled in the first place, such as a severely exposed elevation. Which option fits depends on the borescope findings and the condition of the outer leaf, not on the age of the fill.
Can you top up cavity wall insulation?
No, and this is the point most often misunderstood. Cavity wall insulation cannot be topped up. If a fill has slumped, shrunk or got wet, blowing more material into the same cavity does not fix it. The old material is still there, still wet or still compacted at the bottom, and new fill on top of it does not restore an even layer. The material has to come out first, the cavity has to be cleaned and dried, and only then can new insulation go in, if the wall is still suitable.
That is why extraction exists as a service, and why it costs what it does. Housing association guidance puts extraction at one to two days for a typical house, with the cavity left empty for up to two weeks so it can dry and any remaining material can settle, followed by a post extraction borescope survey to confirm the cavity is clear, and then a refill that takes about half a day. Extraction itself typically costs between 1,000 and 4,000 pounds depending on the size of the house and the material, and a new install costs around 2,200 pounds for a typical home in Great Britain according to the Energy Saving Trust. Set against the savings the Trust quotes, 380 pounds a year for a detached house, 200 pounds for a semi-detached house and 110 pounds for a mid-terrace at July 2026 prices, a refill can still pay for itself in a reasonable time, but only if the wall is suitable this time around. If the wall failed the suitability test the first time, filling it again is repeating the mistake.
Selling a house with 25-year-old insulation
The 25 year mark most often bites during a sale. A surveyor notes the insulation, cannot confirm its condition or its guarantee status from the surface, and flags it. A buyer or a mortgage lender then asks questions, and in some cases asks for the insulation to be removed before they will proceed. That chain of events is the subject of our companion article on why people remove cavity wall insulation, and it is worth reading alongside this one, because removal is sometimes the outcome even when the fill itself is not the problem.
What protects you in a sale is paperwork and evidence. A CIGA certificate showing the install date and the installer, a borescope report showing the fill is dry and in place, and a record of exterior maintenance all answer the questions a surveyor is actually asking. If you do not have the certificate, ask CIGA whether your address is registered before you put the house on the market, and budget for the copy fee, which is more than 50 pounds. If the guarantee has expired, say so plainly and show the borescope evidence instead. A 25 year old fill with a clean borescope report is a much easier conversation than a 25 year old fill with no records at all.
There is one more sale related point. An Energy Performance Certificate may record the cavity as insulated, and that rating was part of the reason many homes were filled. Removing insulation without updating the EPC, or filling a cavity that a surveyor has flagged as unsuitable, can both create problems at the next assessment. Keep the EPC in step with whatever you do to the walls.
What it costs to put things right in 2026
The costs in 2026 are straightforward to summarise, with the usual warning that every house is different and a quote depends on size, access and material. A new cavity wall install for a typical home in Great Britain costs around 2,200 pounds, according to the Energy Saving Trust, and the Trust says it will usually pay for itself in five years or less through energy savings. Extraction of a failed fill typically costs between 1,000 and 4,000 pounds. A borescope survey is often offered free by installers quoting for work, or charged as a modest survey fee by an independent surveyor.
Set those numbers against what the insulation saves. The Energy Saving Trust puts the annual saving at 380 pounds for a detached house, 200 pounds for a semi-detached house and 110 pounds for a mid-terrace, at July 2026 prices. That is the arithmetic that decides whether a refill is worth doing: a working fill in a suitable wall pays for itself, a failed fill costs money twice over, once in the extraction and once in the heating bills it no longer saves. The cheapest option of all is the one nobody charges for: keeping the outer wall in repair so the fill you already have stays dry.
The one cost to avoid is the cost of acting on a scare. A fill that is 25 years old, dry, and in place does not need replacing, and a quote that starts from the calendar date rather than a borescope finding is a quote to get a second opinion on. The guarantee expiring is a prompt to check, not a prompt to spend.
Frequently asked questions
Does cavity wall insulation expire after 25 years?
No. What happens to cavity wall insulation after 25 years is not an expiry: the 25 year figure is the length of the CIGA guarantee, not the life of the material. Mineral wool, polystyrene beads and polyurethane foam are designed to last much longer than 25 years when installed correctly in a dry, suitable wall. What ends at 25 years is the free fix for defects in materials or workmanship, not the insulation itself.
How long does cavity wall insulation last?
Trade guidance typically puts the lifespan at 25 to 40 years as a minimum, with mineral wool rated at 50 to 100 years, polyurethane foam at 50 to 80 years, and bonded polystyrene beads capable of lasting the lifetime of the building. The real answer depends on the material, the quality of the install and whether the wall stays dry. A dry, well installed fill can outlast the guarantee by decades.
What happens when the CIGA guarantee runs out?
You lose the right to a free fix for defects in materials or workmanship. CIGA will no longer arrange an inspection or remedial work under the guarantee, and any repair becomes your cost. The insulation itself is unaffected. If you have a problem and the guarantee is still live, raise it with the installer first and then CIGA, before the expiry date passes.
Can cavity wall insulation be topped up?
No. Failed fill cannot be topped up. Slumped, shrunken or wet material has to be extracted, the cavity cleaned and dried, and new insulation installed only if the wall is still suitable. Extraction typically takes one to two days, the cavity is left empty for up to two weeks to dry, and the refill takes about half a day.
How do I check if my cavity wall insulation is still working?
Look for damp patches or mould on external walls, rooms that never warm up, and cold spots high on a wall, which suggest slump. Check the EPC and ask building control whether the install is recorded. The decisive check is a borescope inspection, where a camera is put into the cavity through a small hole in a mortar joint to see whether the fill is present, dry and in place.
Should I remove cavity wall insulation after 25 years?
Only if it has failed. A dry fill that is still in place should stay, whatever its age. Remove it if it is wet, badly slumped, or made of crumbling urea formaldehyde foam, or if a surveyor has shown the wall was never suitable. Removing good insulation from a sound wall is an expensive mistake, so get a borescope finding before you agree to extraction.
Does old cavity wall insulation affect selling my house?
It can, if there is no paperwork. Surveyors flag insulation they cannot verify, and buyers or lenders may ask for evidence or for removal. A CIGA certificate, a borescope report showing the fill is dry and in place, and a record of exterior maintenance answer those questions. If you have lost the certificate, ask CIGA whether your address is registered before you market the house.
Sources
- Energy Saving Trust, Cavity wall insulation, https://energysavingtrust.org.uk/advice/cavity-wall-insulation/ (read live 20 Nov 2026)
- Cavity Insulation Guarantee Agency, Written evidence to the Energy and Climate Change Select Committee (HEE0107), https://committees.parliament.uk/writtenevidence/60573/pdf/
- Scottish Parliament, Written answer S5W-09467 on the Cavity Insulation Guarantee Agency, https://www.parliament.scot/chamber-and-committees/questions-and-answers/question?ref=S5W-09467
- InterNACHI, UFFI Insulation Inspection, https://www.nachi.org/uffi-insulation-inspection.htm
- Fine Homebuilding, Ask the Expert: Spray foam durability, https://www.finehomebuilding.com/2008/05/14/ask-the-expert-spray-foam-durability
- Westward Housing, Cavity wall insulation, https://www.westwardhousing.org.uk/cavity-wall-insulation
- Post Online, Analysis: Are cavity wall insulation claims the new PPI?, https://www.postonline.co.uk/claims/3831661/analysis-cavity-insulation-bye-bye-to-the-ppi-hello-to-the-cwi
- OSCAR Onsite, CIGA Guarantee Claims, https://oscaronsite.co.uk/ciga-guarantee-claims/